Smallest of the big drivers, the PD-110 is the perfect balance between a hand-held driver and an equipment supported driver. At 109 pounds and a 4" piston, the PD-110 is a powerhouse that will put tough jobs behind you and money in your pocket. The PD-110 si ideally suited for driving 2" to 4" pipe and tube, structural forms, pin piles, dock piles, and 4" x 4" wood.
KIT INCLUDES
| PD-110 Medium Duty Post Driver |
1 |
70014 |
| PD-110 2½" Chuck Adaptor* |
1 |
70624 |
| PD-110 3-4 lbs/ft Channel Post Adaptor* |
1 |
70630 |
| Throttle Valve Kit, includes 5' Hose Whip |
1 |
600000 |
| Filter Regulator Lubricator |
1 |
601128 |
| Transport Cart |
1 |
71202 |
| Hose Whip - 15' 2" |
1 |
71199 |
| MP-3 Manual Post Puller |
1 |
71013 |
| MP-3 Chain Assembly |
1 |
220422 |
| Post Grabber |
1 |
71040 |
* Chuck Adaptors are customizable - see table below for further options
SPECIFICATIONS
| TOP COVER |
Ductile iron casting, high in strength and ductility has 1" (25.4 mm) diameter handles with chain loop designed into the cover for easy handling and carrying. O-Ring sealed. |
| BODY |
Ductile iron casting, with excellent wear resistant characteristics. The air inlet is cast into the body and tapped with 3/4" NPT female threaded ports, along with 1" (25.4 mm) diameter side handles for easy handling. Chuck bolts pass thru the lower body flange into tapped holes in the chuck mounting plate allowing special chucks to be made in a wide variety of shapes and sizes. |
| PISTON |
Alloy steel heat treated with a ground surface with hard chrome plate. Designed with 2 round valve ports to give better lubrication and load distribution to the valve ring while running. |
| MASTER CHUCK & CHUCK ADAPTORS |
The 4 1/4" (107.9 mm) I.D. master chuck is of an all welded, reinforced steel and tubing construction. The chuck is equipped with extra long chuck adaptor attachment lugs. Standard chuck adaptors are available in the following sizes: 2 1/2" ( 63.5 mm) I.D., 3" (76.2 mm) I.D., 3 5/8" (92 mm) I.D. and three channel post chuck adaptors for 1.2 to 1.5 lbs/ft, 2 to 2.75 lbs/ft and 3 to 4 lbs/ft posts. A chuck is available to drive 4" x 4" (101 mm x 101 mm) wood posts and a chuck and drive cap are available to drive 4" x 6" (101 mm x 152 mm) H column guard rail posts. |
| FASTENERS |
S.A.E.Grade 5 bolts with belleville lock washers. All fasteners are plated. |
| AIR CONSUMPTION |
64 CFM (1.81 m3/min) @ 100 PSI (7 kg/cm2) |
| WEIGHT |
116 lbs |
| HEIGHT |
25.75" |
ACCESSORIES AND ADAPTORS
| Throttle Valve Kit with 5" Hose Whip* |
600000 |
|
Chuck Adaptors |
| Filter-Regulator-Lubricator and Carrier pre-assembled |
225005 |
|
35/8" ID Chuck Adaptor |
70622 |
| - Filter-Regulator-Lubricator* |
601128 |
|
3" ID Chuck Adaptor |
70623 |
| - Carrier for Filter-Regulator-Lubricator |
225001 |
|
2½" ID Chuck Adaptor |
70624 |
| Transport Cart |
71202 |
|
2" ID Chuck Adaptor |
70625 |
| Hose Assembly - ¾" Hose up to 25'. Includes assembly, labor and all parts EXCEPT Hose. Add 605006 for each foot of hose needed |
607000 |
|
|
|
| ¾" Extra Hose - price per foot |
605006 |
|
Channel Post Chuck Adaptors |
| Air Hose Assembly - ¾" x 100' |
100048 |
|
1.2 - 1.5 lbs/ft Posts |
70628 |
| PD-110 Chuck Adaptor for the Channel Post Break-Away Anchor System |
70847 |
|
2.0 - 2.75 lbs/ft Posts |
70629 |
| Drive Cap for the Channel Post Break-Away Anchor System |
70836 |
|
3.0 - 4.0 lbs/ft Posts |
70630 |
| |
|
|
|
|
| Low Drive Extension Drive Caps |
|
Post Driver Chucks |
| 1¼" Low Drive Extension Drive Cap for Square Break-Away Bases 1" Pin |
71004 |
|
PD-110 4¼" ID Master Chuck |
70593 |
| 1½" Low Drive Extension Drive Cap for Square Break-Away Bases 1¼" Pin |
71005 |
|
PD-140 4¼" ID Master Chuck |
70594 |
| 1¾" Low Drive Extension Drive Cap for Square Break-Away Bases 1½" Pin |
71006 |
|
4" x 6" H Column Chuck (Chuck Size: 57/8" x 75/8") |
70061 |
| 2" Low Drive Extension Drive Cap for Square Break-Away Bases 1¾" Pin |
71007 |
|
4" x 4" Wood Post Chuck (chuck size: 41/16 x 41/16") |
70063 |
| 2¼" Low Drive Extension Drive Cap for Square Break-Away Bases 2" Pin |
71008 |
|
PD-140 Slott Sheet Pile Master Chuck |
70597 |
| 2½" Low Drive Extension Drive Cap for Square Break-Away Bases 2¼" Pin |
71009 |
|
4" x 6" PD-140 Wood Master Chuck Assy |
71100 |
| |
|
|
PD-140S 4¾" Round Master Chuck |
70644 |
| Schedule 40 Drive Cap with T-Bar & Clip |
|
4" x 6" PD-200 Master Chuck (chuck size 57/8" x 75/8") for the H-Column Guardrail Post System |
70061 |
| 2" Sched 40 Drive Cap with T-Bar and Clip |
71260 |
|
Custom Master Chuck Assembly |
70762 |
| 2½" Sched 40 Drive Cap with T-Bar and Clip |
71261 |
|
|
|
| 3" Sched 40 Drive Cap with T-Bar and Clip |
71262 |
|
|
|
| 3½" Sched 40 Drive Cap with T-Bar and Clip |
71263 |
|
|
|
** FREE ground shipping within Continental United States
DOCUMENTATION
